Clio 1.8 16V l.94 - se tanou 16v (Prodan)

[Markolino]

Priden. Pa pedanten to mi je všeč

[nightmare]

No pa sem tudi sam končno našel človeka, ki je za razumno ceno prodal dele podvozja za Clio Williams.
Gre se za roke in pa polosovine.
Leva roka je kompletna in popolnoma nova, desna je nova a brez zglobov a to ne bo problem in pa roke katere tudi ne kažejo znakov uporabe.






Še mal pa bom dau delat nalepke za na bok.

Če se komu valja ali pa ve za kakšen prednji stabilizator od R19 16V pa naj le javi.


Lp

[Symon]

Opa, opa tole se bo pa zdaj peljalo še boljše pa že original se pelje super. Čestitke.

[UrbanD]

A roke od Williamsa so drugačne koker od ventilarja?
Ker pr mojmu RSu so iste koker pr vseh ph2 cliotih

[nightmare]

A roke od Williamsa so drugačne koker od ventilarja?
Ker pr mojmu RSu so iste koker pr vseh ph2 cliotih

Ja pr Clio I so Williamsove roke drugačne.
Zdej mi je jaasn zakaj se RSi tko slabo pelejo, če je podvozje enako kot pr 1.2. Hec

[kmetek]

Hehe, lepo da tud "konkurenca" ne spi čez zimo

[nightmare]

Hehe, lepo da tud "konkurenca" ne spi čez zimo

Ja tole me je čist zbudilo.

[schkorc]

...
Ker pr mojmu RSu so iste koker pr vseh ph2 cliotih

Si prepričan ?

LP, Primož

[UrbanD]

Da, ker sm primerju in dau iz mostu dol uno k je pokrivlena in dau gor eno k je od 2003 letnika 1.2 16V in je ista.

[MarcY]

Lepo da se ustvarja Še zdaj se ne morem načudit kako pašejo te bele felge. Zmagal si

lahko poveš kako si zadovoljen z s.drive gumami? so mi v ožjem izboru za to leto pa se še odločam med njimi, parado in f1.

[nightmare]

Skoz se mora nekej ustvarjat.
Hvala.

Kar se pa gum tiče sem pa zelo zadovoljen. Nisem nek ekspert, da bi opisoval občutke kako in kaj je za volanom vendar me vedno znova presenečajo tako v suhem kot tudi mokrem.
Prav tako ni moteča obraba niti glasnost.

Bomo videli kako se bodo odrezale spomladi po tem ko so celo zimo stale v garaži.
Če bodo letošnjo sezono še pravtako dobre bodo sigurno ob naslednjem nakupu na avtu iste gume.

[melonca'r]

A niso roke od R19 1.8 16V identične tistim od Williamsa? Če se ne motim sem enkrat bral nekaj o tem na UK forumih..

[Symon]

Da nisi gledal za 172 widetrack Cliota mk1?

Williams Widetrack Information

As you probably know, the Williams has a wider track than a Valver and other Mk1s as standard, which alot of people talk about. The Williams track is 34mm wider overall, and also runs with a thicker anti roll bar, which all improves the handling.

172 Widetrack Information

Now that there are quite a few people that have successfully fitted the 172 widetrack to their Mk1, we know that it is actually wider than the Williams widetrack. We are unsure of the actual figure, but it is at least 10mm overall, if not more!

The other advantage of running 172 widetrack is you get the larger brake setup (280mm disks over 259mm). Plus with the 172 brake setup you have a lot more options for aftermarket brakes (4pots, 6pots, etc), especially when they come up second hand.

Please Note: -----------------------------------------------------------------
The guide is based on fitting the 172 widetrack to a Valver, with regards to parts required and procedure. Its also worth noting that everything fits to a Valver or Williams subframe perfectly fine. Fitting it to a Williams would be the same, apart from you would keep the Williams shock absorbers and Williams anti roll bar.
----------------------------------------------------------------------------------

Parts Required

* 172 Ph1, Ph2 or 182 Wishbones [Picture]
* 172 Ph1 or Ph2 Driveshafts [Picture: Nearside Offside]
* 172 Ph1, Ph2 or 182 Non-Cup Pack Hubs (Bolt Spacing Has To Be 54mm) [Picture]
* 172/182 Hub Bolts + Nuts [Picture]
* 172 Ph1, Ph2 or 182 Brake Calipers (Including Hoses If Possible) [Picture]
* A Pair of 172/182 Brake Disks, 280mm.
* A Set of 172/182 Front Brake Pads
* Williams Anti Roll Bar [Picture]
* Williams Shocks (Can Be Coilovers, Standard Shocks, As Long As They Are Williams Fitment) [Picture]
* Williams Steering Rack (Read Below For Info Regarding Why This Is Needed)

Parts That Dont Fit

* R19 16v Wishbones
* 172/182 Anti Roll Bar [Picture]
* Valver Shocks Of Any Type


Why Do I Need A Williams Steering Rack?

A lot of people that fit Williams widetrack onto their Valver just simply wind the track rod ends outwards to make them longer, so they meet up with the hubs and the wider track. Whilst this is ok on the Williams widetrack setup, we hit a problem with doing it on a 172 widetrack setup as it is wider than the Williams. The track rod ends will not physically wind out far enough to meet the hubs without falling off and/or just being plain dangerous.

A Williams steering rack is wider from factory, to meet the extra width of the williams track. This is ideal for 172 widetrack users as once fitted, the track rod ends can just be wound out as described above, but because the arms on the rack are longer, there is no danger of them being too short.

Williams steering racks are power assisted, and will straight swap onto your valver if you are retaining the power steering setup without a problem. Its just as simple as connecting the hoses up. If you are not running power steering, its possible to pack the inside of the rack with grease and seal the holes, converting it into a 'manual' rack, but keeping the extra length on the arms to meet up with the 172 widetrack.

The other option is to remove the actual arms from the Williams steering rack (as this is the component that is longer), and fit them onto your current Valver steering rack. They are a pain to remove, but it is an option.

Tole bi bil hud projekt, mimogrede.

[nightmare]

So zelo podobne ne pa identične.
Menda se da skombinirat vendar ni vse tako mot mora bit.
Sam teh zadev nisem ravno študiral tako, da bo o tem kdo drug vedel kaj več.

[robi1000]

Niso iste. Castor je drugačen.